JustTeak™ Teak Sealer Large Restoration Kit

Coverage
Teak Cleaner: 5m2(54ft2) per litre
Teak Brightener: 5m2(54ft2) per litre
Teak Sealer (2 Coats): 5.5m2(60ft2) per litre
NOTE: Coverage is approximate as it depends on the absorbency of the Teak.

Technical Data: Teak Cleaner Part 1
Appearance & Odour: Translucent Red Liquid, No Odour
Base: Water
Specific gravity: 1.056
Boiling point: 100 °C
Thinner / Cleaner up: Water

Technical Data: Teak Brightener Part 2
Appearance & Odour: Translucent Green Liquid, Mild Odour
Base: Water
Specific gravity: 1.008
Boiling point: 100 °C
Thinner / Clean up: Water

Technical Data: JustTeak Teak Sealer (Natural or ClearTone)
Appearance & Odour: Beige Opaque Liquid, Hydrocarbon Odour
Specific gravity: 0.84
Thinner: Do NOT Thin
Clean up: White Spirits or xylene
Volatile Organic Compounds: 735 g/L
(theoretical - as packaged)
Flashpoint: 60°C (white spirits) `
Touch Dry at 23°C (73°F) :15-30 minutes
Recoat at 23°C (73°F): Once touch dry

JustTeak™ Application

Part 1 Teak Cleaner
1. Hose down entire area with water.
2. Ensure the teak does not dry during the cleaning process.
3. Applying the Teak Cleaner with a soft polypropylene cleaning pad, gently scrub the product across the grain of the teak. The teak will tum dark brown and the cleaning pad will fill with dirt.
4. Apply to one area at a time then immediately rinse down entire area with water to remove the cleaner. Repeat if necessary.

Part 2 Teak Brightener
1. Following the application of Part 1: Teak Cleaner.
2. Hose down entire area with water.
3. Ensure the teak does not dry during the cleaning process.
4. Apply Teak Brightener with a soft polypropylene cleaning pad, gently scrubbing across the grain of the teak. The teak will immediate lighten.
5. Apply to one area at a time then immediately rinse down entire area with water to remove the Teak Brightener. Repeat if necessary.

Application of the JustTeak Teak Sealer
Preparation
1. For freshly sanded teak: Ensure teak is clean of dust and dirt before application.
2. Weathered and previously coated teak: Clean with JustTeak Teak Cleaner and Teak Brightener to remove previous coatings, dirt and deposits that have turned teak grey, and restore natural colour.
3. Allow teak to dry thoroughly before applying Teak Sealer.
Application
1. For best results apply in temperatures above 10°C (50°F) on a sunny, low humidity day, ensuring the teak is dry. Shake vigorously prior to use. This product must be shaken periodically whilst using to ensure even colouring.
2. Apply the sealer by either brush, pad applicator or rag. Take note to apply sealer along the length of the board to ensure even coating and avoid line marks.
3. Apply generously. Allow to dry, soak up any areas that may have not absorbed the sealer. When touch dry, apply 1-2 subsequent coats until the teak stops absorbing the sealer.
LOOKING AFTER YOUR SEALED TEAK Over time the sealer will start to lose its lustre and water beading capability. A fresh coat of JustTeak: Teak Sealer should be applied to restore the finish. For best results remove the Teak Sealer with JustTeak Cleaner and Brightener and re-apply.

Cleanup
JustTeak Teak Cleaner & Brightener: Clean application equipment and surrounding areas with fresh water immediately after use.
JustTeak Teak Sealer: Clean application equipment immediately after use with white spirits or xylene. Any spills can be cleaned up using a rag soaked in white spirits.