Biocop TF Self-Polishing Bottom Paint, Gallon
- $318.88
- Availability:In Stock
- Brand: Sea Hawk Paints
- Product Code: SH-1200-1 GL
Available Options
Tags: Red 1201-1, Light Blue 1202-1, Black 1205-1, Dark Blue 1230-1, Grey 1231-1, Green 1234-1, Teal 1235-1
Colors: Red 1201-1, Light Blue 1202-1, Black 1205-1, Dark Blue 1230-1, Gray 1231-1, Green 1234-1
Finish/Sheen: Semi-Gloss
Biocide Content: 4.14% (78 g/l)
Copper Content: 38.06% (717 g/l) all colors
Volume Solids: 57% (±2)
Solids by Weight: 80% (±2)
Shipping Weight:
Black - 15.76 Lbs/Gal (7.15 kg/Gal)
Blue - 15.76 Lbs/Gal (7.15 kg/Gal)
Red - 15.76 Lbs/Gal (7.15 kg/Gal)
Dark Blue - 16.0 Lbs/Gal (7.257 kg/Gal)
Green - 15.76 Lbs/Gal (7.15 kg/Gal)
Gray - 17.45 Lbs/Gal (7.915 kg/Gal)
Teal - 15.67 Lbs/Gal (7.107 kg/Gal)
*All colors are not available in all states
Flash Point: 100°F (38°C) VOC: 377 Grams/Liter
Theoretical Coverage: 315 Sq.Ft./Gal. (29.2645 m2) @ 2.9 mils (73.66 µ) DFT.
Typical Film Thickness:
Pleasure craft: 3.0 mils (76.2 µ) dry film thickness(DFT) per coat, (5.3 mils (134.62 µ) wet film thickness(WFT)), 2 coats on the entire hull and a 3rd at the waterline and other high wear areas.
Pleasure craft (California/Reduced CU2O Leach Rate Application): 3.0 mils (76.2 µ) dry film thickness (DFT) per coat, (5.3 mils (134.62 µ) wet film thickness (WFT)), 2 coats on entire hull.
Commercial Marine: 4.0-5.0 mils (101.6-127 µ) DFT per coat by spray application (7.0-8.8 mils (177.8-223.52 µ) WFT), 2 coats on the entire hull and a 3rd at the waterline and other high wear areas. Theoretical Coverage: 315 Sq.Ft./Gal. (29.2645 m2) @ 2.9 mils (73.66 µ) DFT.
Application Controls
Method: This product may be applied by airless and conventional spray, solvent resistant rollers, and brushes.
Dry Times and Overcoating Intervals:
Substrate Temp. | Touch | Min | Max | Minimum Launch |
41°F (5°C) | N/A | N/A | N/A | N/A |
73°F (23°C) | 2 hr | 1 hr | N/A | 12 hrs |
95°F (35°C) | 1 hr | 1 hr | N/A | 12 hrs |
Surface Preparation
Paint only clean, dry surfaces. Remove all grease, oil, wax, or other foreign material by solvent or detergent washing. (SSPC-SPI)
Compatibility: For pleasure craft applications, please refer to our Sea Hawk Compatibility Chart to ensure compatibility when applying Biocop TF antifouling paint over existing bottom paint.
Previously Painted Surfaces: Seahawk Biocop TF is suitable for this substrate. For correct procedures please refer to the Application Guidelines for Fiberglass/Gelcoat.
Fiberglass or Vinyl Ester Hulls: Sea Hawk Biocop TF is suitable for this substrate. For correct procedures please refer to the Application Guidelines for Fiberglass/Gelcoat.
Wood Surfaces: New Work - Sand the wood surface with 80 grit sandpaper, remove the sanding dust with Sea Hawk S-90 Cleaner, allow to dry, and apply the first coat of Sea Hawk Biocop TF bottom paint. Reduce the first coat (only) 20% with Sea Hawk 2033 Thinner to maximize surface penetration. Next, apply whatever seam compound if needed, allow to dry in accordance with the product label, and apply two more coats of Biocop TF without any Thinner reduction.
Aluminum: Biocop TF Antifouling paint may be used on an aluminum hull only when used with the proper barrier coat system described in Technical Bulletin AL1284. Sea Hawk Biocop TF is not to be used on bare aluminum.
Steel Vessels: Sea Hawk Biocop TF antifouling paint is normally used as part of a paint system for underwater hull areas on steel vessels. Nominally, Biocop TF is applied over a properly cleaned existing surface of another antifouling paint or sealer. The surface must be clean and dry prior to application, free of all surface contamination. We highly recommend the hull bottom be high-pressure water washed immediately upon haul out with 2,500-3,000 psi clean fresh water. Some areas may need to be cleaned in accordance with SSPC-SP-1 Solvent Cleaning to ensure all oils, grease, and other contaminants are removed. Please refer to the additional data below and the section on recommended systems for steel below.
Additional Data For Painting Steel Hulls: If the surface to be painted is also to be repaired with an epoxy primer system, we recommend the area first be grit blasted to SSPC-SP-10 ‘near white metal', cleaned free of dust and blast media, and primed in accordance with the primer system specifications. Please refer to the specified primer datasheet for application details. Make sure the first coat is applied within the proper over coating window of the last coat of epoxy primer which is normally while the epoxy is still tacky but cannot be removed with the thumb. Apply at least two coats of Sea Hawk Biocopt TF antifoulant for best performance.
Top Performing Dual-Biocide Biocop TF
Biocop TF was developed as an alternative to tin-based antifouling paints to protect against the harshest marine environments. Using the newest biocide technology, a revolutionary polymer binder system produces an engineered biocide release that leaves no harmful effects on the environment. The result is a multi-season self-polishing bottom paint that provides equivalent protection to tin-based formulas. Once limited to Mega Yachts only, Biocop TF is now legal for all size vessels! Biocop TF comes with a full One Year Manufacturers Warranty against barnacle growth!
- Compare To: Interlux Micron 66
- Reducer: If necessary not more than 10% of Sea Hawk 2033 or 2035
- Llyod's Registry Approved
- Use for Trailer Boats/Power Boats/Sail Boats: Yes
- Warranty: Yes. One-Year Written Guarantee Against Barnacle Growth!
*This Item Ships From Florida ; Click to See Estimated Transit Times
Please Note: This item is not available to ship to the following states: Arizona, Arkansas, Colorado, Idaho, Indiana, Iowa, Kansas, Montana, Nebraska, Nevada, New Mexico, North Dakota, Oklahoma, Utah, Vermont, West Virginia, and Wyoming.
