Interlux Act Bottom Paint

Interlux Act with Slime Fighter Product Specifications
Color Y4490B-Red, Y5590B-Green, Y6690B-Blue, Y6696B-Dark Blue, Y7740B-Gray White, Y7790B-Black, Y8890B-Brown
Finish Matte
Specific Gravity 1.78
Volume Solids 56%
Typical Shelf Life 2 yrs
VOC (As Supplied) 394 g/lt

Click here to view Interlux Act Product Data Sheet

Click here to view Interlux ACT SDS Black

Click here to view Interlux ACT SDS Blue

Preparation of Interlux Act Bottom Paint

PREVIOUSLY PAINTED SURFACES
In Good Condition Remove all traces of loose paint and contamination by sanding the entire surface well with 80 grit wet-or-dry sandpaper. Remove sanding residue.
In Poor Condition Completely remove all old antifouling paint using Interstrip 299E for fiberglass and wood, and by sandblasting to near white metal for steel.
BARE FIBERGLASS It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Remove mold release wax using one of the following Interlux products, Fiberglass Surface Prep YMA601V or Fiberglass Solvent Wash 202 following the product label instructions. Fill any surface imperfections with Interlux Watertite following the label instructions. After the surface has been properly prepared follow the application system below.
Bare Fiberglass - No Sanding System Clean the surface following the preparation procedure above. Apply one coat of Interprotect 2000E or Fiberglass No-Sand Primer. Follow the instructions on the label or product datasheet of the primer used. Following overcoating guidelines for the primer, apply ACT.
Bare Fiberglass -Sanding System Clean the surface following the preparation procedure above. Sand with 80 grade (grit) paper. Remove sanding residue. Apply ACT.
Bare Fiberglass - Blister Prevention System Clean the surface following the preparation procedure above. Sand with 80 grade (grit) paper. Remove sanding residue. Apply Interprotect 2000E to a thickness of 10 mils. Apply at least two coats of ACT allowing appropriate drying times.
BARE WOOD Sand with 80 grade (grit) paper. Remove sanding residue. Apply the first coat of ACT thinned 10% with Special Thinner 216 or Brush-Ease 433. Fill seams, if necessary, with Seam Compound Brown 30. Apply two or more coats of ACT unthinned, allowing for the appropriate dry times.
UNDERWATER METALS Contact the Interlux Technical Service Department at 1-800-468-7589 for full information on how to properly prime underwater metals. Do not use on aluminum.

Method Apply a minimum of 2 coats (3 on bare wood) by brush, short-nap roller or spray. To prevent premature failure, ensure correct amount of paint is applied using the coverage as a guide.
Hints Mixing Stir or shake contents thoroughly before use.
Thinner Special Thinner 216 or Brush-Ease 433.
Thinning Thin only if necessary. Thin no more than 10%. Use Brush-Ease 433 if roller or brush drags during application.
Cleaner Special Thinner 216 or Brush-Ease 433.
Airless Spray Tip Size: 0.53-0.66 mm/21-26 thou. Pressure: 170-204 bar/2500-3000 psi.
Conventional Spray Pressure Pot: Tip Size: 1.8-2.2 mm/70-85 thou. Pressure: 4.08-4.76 bar/60-70 psi (gun pressure); 10-15 psi (pot pressure).
Roller Use a 3/8" nap solvent resistant roller.
Other Take care to apply all the paint calculated even if it means applying an extra coat. Do not apply thin coats.
Some Important Points Colors may fade or change above the waterline. Stir well before use. Product temperature should be minimum 10°C/50°F and maximum 29°C/85°F. Ambient temperature should be minimum 10°C/50°F and maximum 29°C/85°F. Substrate temperature should be minimum 10°C/50°F and maximum 29°C/85°F.
Compatibility/Substrates Not suitable for use over Aluminum/Alloy substrates. Suitable for fiberglass, wood and painted surfaces. Do not apply over tin-based copolymer antifouling paints. Do not use under vinyl based antifouling paints such as VC Offshore or Baltoplate.
Number of Coats 2 coats, 3 on bare wood
Coverage (Theoretical) - 430.3 ft²/gal
Recommended DFT per coat 2 mils dry
Recommended WFT per coat 3.6 mils wet
Application Methods Airless Spray, Brush, Conventional Spray, Roller