Awlgrip HDT Clearcoat Activator

Volume Solids 49% (mixed product)
Specific Gravity 0.98 - Base
Available Packs 1 US Gallon (=3.78L) for Base and Curing Solution
1 US Quart (=0.95L) for Activators
Base Awlgrip HDT Clearcoat (OC0300)
Converter Awlgrip HDT Curing Solution (OC0010)
Reducer Activators:
Awlgrip Slow Activator (OA0010)
Awlgrip Fast Activator (OA0020)
Activators are essential for the technology of this product to achieve the required curing.
Equipment Cleaning T0001, T0002, T0003
Typical Shelf Life 2 years for Base and Activators
1 year for Curing Solution

TDS – AwlGrip HDT Clearcoat

Surface Preparation

For the application of the basecoat please refer to the Awlcraft SE TDS.
Awlcraft HDT Clearcoat should be applied over Awlcraft SE Basecoat or previous Awlgrip/Awlgrip HDT/Awlcraft Topcoat. Over basecoat ensure the surface must be clean and dry. Wipe with surface cleaner T0170 (US) or T0340 (EU) using the two cloth wipe down method. Over Awlgrip Topcoat/Awlgrip HDT/Awlcraft 2000 topcoat sand topcoat with P400 to remove the gloss and clean with surface cleaner T0170 (US) or T0340 (EU) using the two cloth wipe down method.
Do not use unless mixed thoroughly with the curing agent at specified ratio. Avoid painting in direct sunlight. Substrate temperature should be minimum 5°C/41°F and maximum 30°C/86°F. Product temperature should be minimum 15°C/59°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 30°C/86°F. Avoid applying late in the evening as condensation can cause a loss of gloss during overnight cure. Allow to dry in a well ventilated environment.
The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation.

Mixing & Reduction
Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application
of a small sample before full-scale application is recommended.
Mix Ratio (by volume):
1:1:0.25 (Base:Curing Solution:Activator)
Induction time = 15 minutes.
Mix to a smooth, homogenous mixture.
Awlgrip HDT Clearcoat is designed for spray application only. Correct choice of activator must be made according to the application conditions and project size.
General guideline:
15-23ºC OA0020
20-30 ºC OA0010- OA0020 with a 50:50 mixture by volume
>30ºC OA0010
      
Mix to a smooth, homogenous mixture. Awlcraft SE basecoats are designed for spray application only and have a significantly shorter pot life than regular topcoats. DO NOT add accelerators to Awlcraft SE.

Application

To apply Awlcraft SE Basecoat please refer to the Awlcraft SE TDS. To ensure optimal adhesion between coats Awlgrip HDT should be applied according to the overcoating intervals as described in the Recoatability & Drying Times section. Apply a full coat of Awlgrip HDT Clearcoat to the surface. Allow tack coat to "flash off" 30-45 minutes depending on application conditions. Apply a slightly heavy second coat. A third coat can be applied to reach DFT if needed.
Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary.

Recoatability & Drying Times
The data given for recoatability is not exhaustive. Actual recoatability can vary according to individual conditions, climate and surroundings. If unsure, consult your local technical service representative before proceeding.

Overcoated By: Awlcraft 2000, Awlgrip HDT Clearcoat 
Temp: 35°C (95°F) 30 Minutes Min, 3 days MAX 
Temp: 23°C (73°F) 30 Minutes Min, 3 days MAX

Temp: 15°C (59°F) 120 Minutes Min, 3 days MAX

The figures in this table refer to overcoating Awlcraft SE Basecoat with Awlgrip HDT Clearcoat.

Awlcraft SE Basecoat surface must be kept clean at all time before clearcoat application. To reduce dust contamination, clean compressed air or tack rags should be used over Awlcraft SE Basecoat. Oil contamination should be removed using light amounts of Awlgrip Wipe Down Solvent (NA/AP: Awlprep T0008; EU: Surface Cleaner T0340). In case of heavy contamination contact your local Representative.